Sorbent Tube Accessories

---

Adjustable Low Flow Tube Holders

These tube holders allow higher flow pumps to sample in the 5 to 500 ml/min flow range, and provide for multiple tube sampling. Flow rate can be adjusted using the convenient flow adjust screw on the holder.

Adjustable Low Flow Tube Holder Type		Qty.	Cat. No.
Single		each	224-26-01
Dual		each	224-26-02
Tri		each	224-26-03
Quad		each	224-26-04

Adjustable Low Flow Tube Holders Operating Instructions (PDF)

---

Plastic Protective Covers

Sorbent sample tubes size determines protective cover size. Collar clips are attached to the plastic tube cover for your convenience. Sample tubes sizes and recommended covers can be found on the sorbent tube pages. Protective covers require low flow holders above.

Plastic Cover	Tube Specifications	Qty.	Cat. No.
A	6 mm OD x 70 mm Length	Each	224-29A
B	8 mm OD x 110 mm Length	Each	224-29B
C	10 mm OD x 150 mm Length	Each	224-29C
D	10 mm OD x 220 mm Length	Each	224-29D
V	OVS Tubes (Do not use an adjustable low flow holder)	Each	224-29V
P	Low-volume PUF (Do not use an adjustable low flow holder)	Each	224-29P

---

Constant Pressure Controllers (CPC)

When using the following pumps for low flow applications, use a CPC with an adjustable low flow holder (above)

Pump Model		Qty.	Cat. No.
AirChek 2000, AirChek XR5000, and AirChek 52 CPC Operating Instructions PDF		Each	224-26-CPC
Pocket Pump and AirLite CPC Operating Instructions PDF		Each	224-26CPC-10

---

Low Flow (5 to 500 ml/min Adapter Kits)

Includes Constant Pressure Controller (CPC), single Adjustable Low Flow Holder, and Type A tube cover

Description	Cat. No.
AirLite Kit	110-500
AirChek 52, AirChek XR5000, and AirChek 2000	210-500

 

Low Flow Tube Holders with Plastic Cover For 222 Series and Pocket Pumps SKC Sample tubes – the most widely used in the industry – assure a positive seal between the sample pump and the sample tube. These all-in-one holders each include a holder with tubing and an lightweight protective plastic tube cover with collar clip. Choose the appropriate holder by matching the tube cover letter in the sorbent tube pages with the cover letter in the table below. Use these plastic holders with the Pocket Pump and 222 Series pumps only.

Plastic Cover	Tube Specifications	Qty.	Cat. No.
A	standard 6 mm OD x 70 mm long	Each	222-3-1
B	7 or 8 mm OD x 110 mm long	Each	222-3L-1
C	10 mm OD x 150 mm long	Each	222-3XL-1
D	10 mm OD x 220 mm long and shorter tubes	Each	222-3XD-1

---

Accessories

Description		Cat. No.
Breaker/Capper, stainless steel Size S, 6 and 7 mm OD tubes		222-3-50
Breaker/Capper, stainless steel Size L, 8 and 10 mm OD tubes		222-3-51
Tube Scorer/Breaker, for 6-mm OD tubes; scores and breaks end tips off glass tubes leaving a clean, smooth opening		800-01200
Quality file for Tips		P222318
Charcoal Pick		222-3-20

---

Tubing/Adapter Kit for Calibration of OVS Tubes

This new kit contains two sections of tubing and a tubing adapter to facilitate calibration of a sample pump when using an OVS Sorbent Tube. OVS Tubing/Adapter Kit includes 2 sections of tubing and tubing adapter

OVS Tubing/Adapter Kit Cat. No.........................................224-31

 

---

This page was last modified December 17, 2008